SLCX560 4 3AC Revolution ATEX Long Cased Axial Fan Three Phase AC 560mm

The Elta SLCX560/4-3AC is a 560mm ATEX rated long cased axial fan from the Elta Revolution SLCX range, built for duct mounting in hazardous areas. It moves up to 13460 m³/h at free air and still delivers 9896 m³/h at 200 Pa, driven by a 1.5 kW 4 pole three phase motor running at 1380 rpm.Elta mark the SLCX to Ex h IIB+H2 T4 Gb, classified for constructional safety under the 2014/34/EU directive. The casing is heavy gauge sheet steel, roll formed, welded and dip galvanised after fabrication, and the adjustable pitch aerofoil impeller has carbon filled anti-static blades on a die cast aluminium hub. It is fixed speed, direct on line, and Elta give a 12 month warranty. 3 Phase AC Motor Up to 13460 m³/h Fixed Speed What it is best used forHigh volume ventilation of large classified spaces with moderate ductwork: digester and sludge buildings, large battery charging halls, chemical warehouses and process buildings. It moves 13460 m³/h free air and 12049 m³/h at 100 Pa from a 1.5 kW motor.Its curve stops at 200 Pa. For a high resistance duct the Elta SLCX500/2B-3AC reaches 500 Pa, but at much higher power and noise. It is not suitable for Zone 0, and the marking is for gas atmospheres only, so ask us before specifying it for a combustible dust zone. Zone classification is the responsibility of the installer or site duty holder: check the Ex h IIB+H2 T4 Gb marking against your hazardous area classification before ordering.Why choose this over alternativesChoose the SLCX only where the area is classified as hazardous. Its Ex h IIB+H2 T4 Gb marking, anti-static impeller blades and ATEX build are what you are paying for; the standard Elta SLC560/4A-3AC is the non-ATEX version of a similar size for ordinary ventilation and costs considerably less, but must never be used in a zoned area.It gives similar free air volume to the 2 pole Elta SLCX500/2-3AC for less than 70% of the motor power, and is quieter at 65 dB(A) inlet and 62 dB(A) outlet at 3m. The Elta SLCX630/4-3AC is the next size up.Installation notes Electrical installation must comply with BS7671 and EN60079-0 and be carried out by competent persons. Provide a means of electrical isolation in the fixed wiring and wire to diagram 152-612 through the M20 cable entry, with the M6 earth stud bonded. The fan can be mounted at any angle. Seal all flanges with an oil and diesel resistant silicone sealant, and fix to the 645mm flange using the 12 holes of 12mm diameter on a 620mm PCD. Elta state the zone inside and outside the fan can differ by no more than one zone (for example Zone 1 inside, Zone 2 outside), except when fitted with a flexible duct connection, where there is no zone separation. It is not suitable for Zone 0. It is fixed speed, direct on line. Elta must be consulted before any speed controller or inverter is used, and the controller in the ancillary pack is not ATEX rated and must be mounted outside the hazardous area. At start up check rotation, airflow direction and that motor current does not exceed the nameplate. Inspect AV mounts and earth bonding every 6 months, and check impeller tip clearance every 26,000 hours or 3 years. You'll also need Elta matching flanges 560mm (061B-0560) sold each, one per duct connection Elta ancillary pack APK560/003 available to order, ask us. Its controller is not ATEX rated and must be mounted outside the hazardous area. Elta AV mounts 062-003 available to order, ask us Elta impeller side guard 078C-0560-C available to order, ask us. Guarding is not included with the fan. Browse more cased axial fans, axial fans or Elta fans, or call us for help choosing the right fan.Specifications Model SLCX560/4-3AC Type ATEX long cased axial fan, duct mounted Diameter 560mm Max airflow 13460 m³/h Static pressure 200 Pa Motor Three phase AC, 380-415V 50Hz, 4 pole, 1380 rpm Power 1.5 kW (3.50 A peak) Noise 65 dB(A) inlet, 62 dB(A) outlet at 3m ATEX marking Ex h IIB+H2 T4 Gb Warranty 1 Year Manufacturer Airflow at 100 Pa 12049 m³/h Airflow at 200 Pa 9896 m³/h Starting current 15.40 A, direct on line Speed control Fixed speed, consult Elta before using a controller or inverter Directive 2014/34/EU, not suitable for Zone 0 Ambient temperature minus 20°C up to 40°C Impeller Adjustable pitch aerofoil, carbon filled anti-static blades, LM24 aluminium hub, balanced to ISO 14694 G6.3 Casing Heavy gauge steel, dip galvanised to BS EN ISO 1461 Casing length 450mm Flange 645mm outside diameter, 12 holes 12mm diameter on 620mm PCD Cable entry M20, terminal box on casing Wiring diagram 152-612 Weight 63 kg Manuals & Guides Elta Revolution SLCX ATEX Datasheet Elta Revolution SLCX ATEX Installation Manual