Clearflow CFHT560 Roof Fan Three Phase AC 560mm

The Elta Clearflow CFHT560 is a 560mm roof mounted centrifugal fan with vertical discharge, rated for operating temperatures up to +120°C. It moves up to 9526 m³/h at free air and 6732 m³/h at 500 Pa, the highest pressure in Elta's performance table, and it throws the exhaust upwards, away from occupied areas.The three phase TEFC motor (380-415V 50Hz, 4 pole, 1455 rpm) sits out of the air stream, is IP55 rated with sealed for life bearings and Class F insulation, and drives a free running impeller with 7 backward curved, powder coated steel blades. The casing is pre-galvanised sheet steel, a wind guard is fitted as standard, and Elta give a 12 month warranty. 3 Phase AC Motor Up to 9526 m³/h Speed Controllable What it is best used forHigh volume roof extract for hospital and institutional kitchens, factory process areas, bakeries and forges, where the air may be up to 120°C. It moves 9526 m³/h free air and 6732 m³/h at 500 Pa, enough for a large canopy line or several hoods on one duct.It is not a smoke extract fan: Elta rate it for continuous running with air up to +120°C and the datasheet gives no smoke or fire temperature/time rating, so use a certified smoke fan where one is specified. It is three phase only and must run through an Eltadrive variable speed drive, so budget for the drive. For a ducted fan inside the building rather than on the roof, look at a high temperature box fan instead.Why choose this over alternativesA roof mounted fan keeps the motor and the noise outside the building and puts the discharge high above the roof line. Unlike a roof fan with its motor in the airflow, the CFHT560 keeps its motor out of the air stream and is rated for air up to +120°C, so it suits grease laden or hot extract that would shorten the life of a fan with the motor in the airflow. The base can sit on a roof pitched at up to 15°, which can save building a level upstand.The Clearflow range runs from 350 to 630mm. For a smaller duty, the Elta Clearflow CFHT500 gives 6790 m³/h free air. If you need more, the Elta Clearflow CFHT630 gives 13748 m³/h. Elta's data show overall efficiency of 52.5% at the best efficiency point for this size.Installation notes Mount on the roof with the discharge vertical. The fan can be fitted at angles up to 15°, so it can go directly onto a pitched roof. An Eltadrive variable speed drive must be installed with this fan. For a single phase site Elta list 149-ODE3-12150-1KB1Y (IP66) or 149-ODE3-12150-1KB12 (IP20), which run the three phase motor from a single phase supply; for a three phase site use 149-ODE3-14150-3KA1Y (IP66) or 149-ODE3-14150-3KA12 (IP20). Wire to Elta wiring diagram 152-600 and provide a local means of isolation. Use an IP66 drive if it will be mounted outside next to the fan. The fan weighs 87 kg. Check that the roof, upstand or kerb can carry it, and leave safe access for cleaning. The wind guard lifts off for cleaning, and the motor sits out of the air stream, so grease build up can be cleaned from the impeller and casing without disturbing the motor. You'll also need Eltadrive variable speed drive for single phase sites: 149-ODE3-12150-1KB1Y (IP66) or 149-ODE3-12150-1KB12 (IP20). Available to order, ask us. Eltadrive variable speed drive for three phase sites: 149-ODE3-14150-3KA1Y (IP66) or 149-ODE3-14150-3KA12 (IP20). Available to order, ask us. Browse more roof fans, high temperature fans or commercial kitchen extractor fans, or call us for help choosing the right fan.Specifications Model CFHT560/4-3AC Type High temperature roof mounted centrifugal fan, vertical discharge Size 560mm Max airflow 9526 m³/h Static pressure 500 Pa Motor Three phase AC TEFC, 380-415V 50Hz, 4 pole, 1455 rpm Power 1.833 kW (3.27 A peak at 400V) Noise 61 dB(A) inlet, 64 dB(A) outlet at 3m IP rating IP55 motor Warranty 1 Year Manufacturer Max air temperature +120°C operating temperature (not smoke rated) Airflow at 100 Pa 9155 m³/h Airflow at 200 Pa 8705 m³/h Speed control Eltadrive variable speed drive, must be installed Impeller Free running, 7 backward curved steel blades, powder coated Casing Pre-galvanised sheet steel, wind guard fitted Mounting Roof, up to 15° pitch Motor insulation Class F Overall efficiency 52.5% Wiring diagram Elta 152-600 Weight 87 kg Manuals & Guides Elta Clearflow CFHT Datasheet